VFFS seal troubleshooting starts by naming the symptom — and tracing it back to the one dial behind it.

Heat sealing jaws closing on film. The jaw faces, not the setpoint on the screen, decide whether the seal holds.
Name the Symptom Before You Touch a Setting
Heat, pressure, and dwell time make the seal:
Heat softens the sealing layer.
Pressure squeezes the two layers into one.
Dwell time keeps them there until they fuse.
Every dial on the moves one of those three, and no other. So one bad bag can mean several different things.
The mark is the clue:
Not enough heat: the seam pulls apart in your hand.
Uneven pressure: one end of the bag goes weak.
Too little dwell: looks finished, opens under a light pull.
Name the mark and you're down to one suspect. Except the suspect might not be a dial at all — it might be the film, or the product. Two short tests sort that out:
Swap the film. Take a roll that seals well on another line, load it, run 20 bags at your current settings. Seals recover? You've found it — the film was the variable.
Run empty. Same good roll, 20 bags, nothing inside. Hold up? Then product's landing between the jaws.
Twenty bags is our own quick-check number. Not an industry standard — just the size we use. Your QC team may trust a different count; use theirs. Take one variable away and what's left has nowhere to hide.
Sticky or fragile product misbehaving in the bag? That's a filling problem, not a seal problem. Different job.
Neither test points anywhere? Then it's the machine — the four sections below go through the symptoms one by one.
Candy lines get their own version of seal trouble — melt, sticking, bloom — and there the fix comes down to heat, speed and seal choice, which our page works through one by one.
A Leak That Opens Days Later
A leak lets air, moisture, or smell out — and the bag can still look fine on the shelf. Usually the customer finds it before the operator does.
Start with the gap between the setpoint and what the jaw actually holds while it's running. The controller can show the right number while the jaw itself runs cooler, so take the temperature and pressure off a live machine. Last week's setup sheet won't tell you.
Where to start with a leak? Not the dial. Two checks narrow the search:
Seal the cross seam on some bags, the vertical seam on others. A leak on one and not the other tells you which jaw it is.
Check the roll actually has a sealing layer that fuses at the heat your machine can hold. Wrong layer, no sound seal — ever.
A water dip settles it: seal a few empty bags, press them gently under water, watch the seam.
A steady line of bubbles in one spot: physical gap. Seepage along the whole seam: a setting or film problem.
Thick product leaking around the seal is related, but it's a different problem: on sauce lines the culprit is usually drip putting product on the seal in the first place, and our page works through the pumps and nozzles that stop it.
When the Seal Peels Apart in Your Hand
A weak seal sits fine in the pile. Then someone pulls it and it opens. Film and heat first — tool kit stays shut for now.
Every sealing layer fuses inside a particular temperature band. Ask for more heat than the jaw can deliver at a safe speed and the bond never forms; slow the line down and it helps, right up until dwell starts scorching the film instead.
The jaw faces. Worn PTFE tape breaks heat transfer — part of the seam never gets the energy it needs. A damaged surface does the same in one spot, bag after bag.
Put these on the check sheet:
The batch number on the film roll running right now.
The condition of the PTFE tape on both jaw faces.
Whether the weak spot keeps landing in the same place.
Weak spot wandering? It's the film. Same place every time? It's the jaw.
Film That Burns or Discolors
Brown marks. Pinholes. A seal that tears like paper — the loudest symptom there is, and it means the machine's running hotter or slower than the film allows. Watch only the temperature dial and you'll miss the speed side of it.
Compare the actual jaw temperature with the setpoint.
A drifting sensor can push a correct dial well past what the film tolerates, while the display still shows the number you typed in.
You need two numbers:
How hot the jaw actually runs, not what the screen says.
Line speed when the burned bags came off.
Slow the line and dwell time rises, even when the temperature readout hasn't moved — which is why a burn so often turns up right after a routine speed change. With a burn, speed matters as much as heat.
When Only Part of the Seam Holds
Part of the seam holds and the rest peels. That's hardware, not the recipe — turning up the heat rarely helps, because the weak side simply isn't getting the same pressure as the strong side.
Misaligned jaws press unevenly across the bag width; a damaged sealing surface does the same in one repeatable spot. Either one looks like a heat problem until you look at the jaws themselves.
A plain paper strip gives you a fast answer. Feed it through the jaws at sealing position and study the imprint:
An even mark across the full width means the jaws meet cleanly.
A pale end points to a pressure or alignment fault.
A faint band in the middle points to wear on the sealing surface.
That tells you how the jaws meet. Nothing about heat. Use it to rule hardware in or out, then check the controller reading.
When Product Sits in the Seal
A bag can leave the jaws with product trapped in the weld. It looks like a weak seal, but the cause sits upstream at the filler, and this is where VFFS seal troubleshooting most often points the wrong way.
Most of the time the trail leads to the filler:
A weigher that releases too early, so product is still falling while the jaws close.
An auger that drips after the screw stops turning.
Fine dust hanging in the air long enough to settle on the sealing area.
Different source, different fix:
A cut-off gate holds the drop until the bag clears.
An air blow — or a de-aerating filler — for product that carries dust or trapped air.
Ask for the principle, not a part number copied from another line, and treat it as a branch of the elimination step: if the empty-bag test sealed cleanly, start here before touching any heat dial.
If the weigher is the source, the fix depends on how the product behaves on the way down — short drop, clean discharge, low-impact handling — and is decided by product behavior, not head count.
Keep a Record You Can Hand to Someone
One change. Measure it. Move on. The method only works when the record's honest.
Catch a Bad Film Before It Reaches the Line
Ask your film supplier for a certificate of analysis with each roll and keep it with the batch record. Four lines on it matter:
Which resin forms the sealing layer, and how thick is it?
When was the corona treatment applied, and how was the roll stored?
How much slip additive does the film carry?
Does this roll match the batch that sealed well?
Every answer takes a guess off the table — a sealing layer that melts below your jaw's heat burns before it bonds.
Corona treatment fades with time and poor storage, and too much slip additive migrates to the surface and weakens the bond. Keep the comparison in your maintenance records. A film change should never arrive as a surprise.
Change One Thing, Run Twenty Bags
Pick one change. Run 20 bags. Water dip or drop test. Log the result before touching anything else.
Don't change heat, pressure, and dwell together. If the seals improve you won't know which change did it, and the next shift starts guessing from scratch.
One change per run also hands you a record a supplier can actually use. Beats "we tried a few things."
Know When the Fault Is Not a Setting
Some seals won't come back with settings. A jaw that no longer holds heat, a worn sealing face, a sensor drifting between readings — those need a part and a technician.
Two clean one-variable cycles and no improvement? Stop. Escalate. A setup problem and a hardware problem need different help — and repeated adjustment costs production time either way.
Stuck at the escalation point? and we'll help narrow it down. Keep the batch records with the test-bag results. Six months from now that log answers, faster than anything else, whether a fault started with the film or the jaws.
FAQ
What Should I Check First When a Seal Is Weak?
Film and product first. Run 20 bags on a roll that seals well elsewhere, then 20 empty bags. Seals recover on the good roll, the film was at fault; empty bags hold, the product was landing in the seal. The machine settings come last.
How Often Should Seal Jaws Be Cleaned?
There's no fixed interval that fits every product. Clean when you can see residue on the jaw face, or when test bags come out uneven. Put it in your maintenance routine and write down what you found, so the next operator knows what a clean jaw looked like.
What if Product Keeps Landing in the Seal?
Work upstream of the jaws: weigher release timing, auger drip after the screw stops, dust in the fill zone. A cut-off gate fits one case, an air blow another — match the fix to the source instead of changing the seal setting and hoping.





